• Networking

  • How to use SNR tweaking for a faster or more stable connection

Adnan wrote
313 wrote
Kareem wroteFor D-link modems ...

https://i.gyazo.com/2861cf1a5e5782159e75c72753e15955.png

adsl configure --snr xx

To understand more the value of XX, check the link below :

http://www.increasebroadbandspeed.co.uk/SNR-tweak


basically you wanna reduce the SNR Margin ( not SNR ) in steps of 3dB. reduce and test stability. mine won't go below6 dB

I tried Kareem's Tutorial but with no luck, The error is that Invalid parameter.

My guess is that I haven't entered through configuration terminal since the command

>adsl snr
shows
------the table SNR per tones(carriers) of the interface ADSL2+-----

Downstream Upstream
168 266

any tutorial for dummies?
What's your router model ?


DLINK DSL-2750U

Click here to see the photo
The C1 revision of your modem has a Broadcom chipset, however the U1 has a Realtek one. Now if you have a Broadcom chipset and it didn't work, it might be that the manufacturer removed the feature.
Kareem wroteNo way to tweak the thomson TG585 V8 although it's very easy on the V7, the V8 adslctl command was removed .
How can we do it on the v7? I've been trying a lot, and it can't seem to work.
mohammadk97 wrote
Kareem wroteNo way to tweak the thomson TG585 V8 although it's very easy on the V7, the V8 adslctl command was removed .
How can we do it on the v7? I've been trying a lot, and it can't seem to work.
There is a custom Firmware for the V7. Check online but I am not responsible for any damage.

Meanwhile :

I noticed today that my DSLAM's target SNR margin was set to 8dB (I am on Sodetel DSP, but I'm not sure who controls this). It was set to 10dB until yesterday. It seems that they're able to put more load on the network so they decreased the SNRM for extra speed.
Adnan wroteI noticed today that my DSLAM's target SNR margin was set to 8dB (I am on Sodetel DSP, but I'm not sure who controls this). It was set to 10dB until yesterday. It seems that they're able to put more load on the network so they decreased the SNRM for extra speed.
Usually it should be the other way around when they have high load since higher SNRM improves stability unless i'm mistaken.
Kareem wrote
Adnan wroteI noticed today that my DSLAM's target SNR margin was set to 8dB (I am on Sodetel DSP, but I'm not sure who controls this). It was set to 10dB until yesterday. It seems that they're able to put more load on the network so they decreased the SNRM for extra speed.
Usually it should be the other way around when they have high load since higher SNRM improves stability unless i'm mistaken.
Not sure we understood each other correctly.

But what I'm speculating here, rephrased:

Sodetel put the target SNRM to 10dB initially. They tested it and found that their network can handle more load and still be stable, so they lowered the SNRM to 8dB to give more speed. Now the load is higher than before, but still not high enough to cause stability problems from their side.
@Adnan, what about Thomson modem tg 585 v7
@Mylo89 mohamadk97 has the same modem. It has a broadcom chipset so in theory the tweak should work. But unfortunately it didn't for him. Can you try the broadcom method provided by Kareem to confirm ?

If it fails, you can try flashing a custom firmware as Kareem suggests.
So i just realised my router can't adjust SNR margins. It's an TP-Link VR400. :(
@dio it really seems that a whole lot of modems don't support this feature, I don't know why. You always have the option of contacting your ISP. Good luck.
Does anyone know if the Cisco-Linksys XAC1900 Dual Band AC1900 will be able to edit these values? I don't have the modem but I'm thinking to buy it
Adnan wrote@dio it really seems that a whole lot of modems don't support this feature, I don't know why. You always have the option of contacting your ISP. Good luck.
Already did. Asked them if they could adjust the SNR margin on my line, they said it's not possible to do it for individuals, if they adjust it, they will have to do it for the whole area.

Which is starting to explain the fact that why my connection has decreased from 12 to 5 in a month.

Speaking of which, does anyone now if Ogero can individually adjust the SNR margin for a user? If so, who can I talk to to adjust it. Mr Rifai perhaps?
8 months later
My modem is speedtouch 546 v6 with firmware 6.2.29.2. I need to downgrade to version 6.1 to be able to use SNR tweaking as this feature was disabled in version 6.2. I could not find the firmware anywhere except on this forum http://www.speedtouchforum.de/viewtopic.php?t=1089#8355

They seem to be the right firmware but I am afraid of bricking my modem. Is there any precautionary step i can do to gaurantee I can get my modem to work in case they are not the right firmware or something goes wrong? For example can I download/backup the firmware on my modem before I start? What are your recommendations?
3 months later
I want to buy a new modem specifically to get the snr tweaking feature. Can you please recommend a good modem that is guaranteed 100% to have this feature?
2 years later
new_user wroteI want to buy a new modem specifically to get the snr tweaking feature. Can you please recommend a good modem that is guaranteed 100% to have this feature?
ASUS allows you to tweak you SNR by tweaking the DB in the interface.
Idler wrote
new_user wroteI want to buy a new modem specifically to get the snr tweaking feature. Can you please recommend a good modem that is guaranteed 100% to have this feature?
ASUS allows you to tweak you SNR by tweaking the DB in the interface.
True but it only works on adsl connection in the interface and not VDSL

For VDSL, you have to use the command line:
wan vdsl2 set target_snrm XXXX
wan adsl reset

However, Asus modems don't have a Broadcom chipset so they are more prone to CRC errors and are less stable on noisy lines.
I had the same thought until i purchased one, if you tweak it just about right its stable and pretty good i've been on stable 4mbps for about a year since i got it with minimum of CRC errors around 8000/month also you may install open source firmware that gives you a major boost to tweak it through SSH

wollyka wrote
Idler wrote
new_user wroteI want to buy a new modem specifically to get the snr tweaking feature. Can you please recommend a good modem that is guaranteed 100% to have this feature?
ASUS allows you to tweak you SNR by tweaking the DB in the interface.
True but it only works on adsl connection in the interface and not VDSL

For VDSL, you have to use the command line:
wan vdsl2 set target_snrm XXXX
wan adsl reset

However, Asus modems don't have a Broadcom chipset so they are more prone to CRC errors and are less stable on noisy lines.
2 months later
wollyka wrote
Idler wrote
new_user wroteI want to buy a new modem specifically to get the snr tweaking feature. Can you please recommend a good modem that is guaranteed 100% to have this feature?
ASUS allows you to tweak you SNR by tweaking the DB in the interface.
True but it only works on adsl connection in the interface and not VDSL

For VDSL, you have to use the command line:
wan vdsl2 set target_snrm XXXX
wan adsl reset

However, Asus modems don't have a Broadcom chipset so they are more prone to CRC errors and are less stable on noisy lines.
i am doing that using putty to my asus modem but nothing is changing on the asus dashboard


also it lets me change the vdsl snr not the adsl and my connection is adsl
TokMe3HrsToSolveChallenge wrote
wollyka wrote
Idler wrote
ASUS allows you to tweak you SNR by tweaking the DB in the interface.
True but it only works on adsl connection in the interface and not VDSL

For VDSL, you have to use the command line:
wan vdsl2 set target_snrm XXXX
wan adsl reset

However, Asus modems don't have a Broadcom chipset so they are more prone to CRC errors and are less stable on noisy lines.
i am doing that using putty to my asus modem but nothing is changing on the asus dashboard


also it lets me change the vdsl snr not the adsl and my connection is adsl
Did you try using wan adsl set target_snrm XXXX or wan adsl2 set target_snrm XXXXinstead of vdsl2?
Also what target_snrm are you using?

When I had adsl, I was using the Asus interface and it was working just fine. When I switched to VDSL, i had to use putty and the commands