LebGeeks

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

btw I was reading something..can't you just login to your router using IE  then Home > SpeedTouch > Configuration > Backup & Restore and save a configuration file ?

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

i didnt understand..where should i paste the output of the command? in that user.ini file?

if you go to /dl and you type ls, what is the output.

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

btw I was reading something..can't you just login to your router using IE  then Home > SpeedTouch > Configuration > Backup & Restore and save a configuration file ?

holy crap!! it worked!

password=_DEV_AF8F30DEB758558F status=enabled
could you decode it for me please?

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Hold on please.

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

I think that it was hashed against the serial number. Anyway we can try this.

Press Disconnect so that the password is shown with **** and then put this on the address bar and press enter.

javascript:(function(){var s,F,j,f,i; s = ""; F = document.forms; for(j=0; j<F.length; ++j) { f = F[j]; for (i=0; i<f.length; ++i) { if (f[i].type.toLowerCase() == "password") s += f[i].value + "\n"; } } if (s) alert("Kwdikoi pou vrethikan:\n\n" + s); else alert("Den yparxoun formes kwdikwn s afti ti selida.");})();

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Last edited by belal (October 11 2009)

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

where is the password shown ? as ****

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

sorry.
here it is:(btw i cannot paste anything in that small window 's address bar. the only choice is to 'copy'..check it:(these alcatel fags know how to work!:S) & the password is always blank there . mafi *****..

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

IF you telnet to your router, can you execute the command EXPERT ?

Last edited by Kareem (October 11 2009)

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

No.it seems my firmware is updated!!

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

grrr.. I will keep on searching but it seems a bit complex. unless someone here has decrypted similar type of passwords. AFAIK hash is one way encryption and the device is using the serial number to encrypt the pass.

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

3azabtak man,sorry i wasted you time, thank you for your efforts :)

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Nah im not gonna stop, we keep on reading. Ill post some updates as soon as I find anything interesting.

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Values starting with _DEV_
Is a reversibly device-dependent encrypted value. Is a device-dependent reversibly encrypted value. This encryption is used for This encryption is used for
saving sensitive values that should not be re-used on another SpeedTouch™ saving sensitive values that should not be re-used on another SpeedTouch ™
device, yet for which the clear-text value must be retrievable for the Speed- device, yet for which the clear-text value must be retrievable for the Speed -
Touch™ device eg the PPP password. Touch ™ device eg the PPP password.
The encryption algorithm is unique for each individual SpeedTouch ™. Configuration
files with _DEV_ values for variables can only be used by the SpeedTouch™ files with _DEV_ values for the variables can only be used by the SpeedTouch ™
device the _DEV_ value was originally generated on.

Last edited by Kareem (October 11 2009)

belal

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Press Disconnect so that the password is shown with **** and then put this on the address bar and press enter.

javascript:(function(){var s,F,j,f,i; s = ""; F = document.forms; for(j=0; j<F.length; ++j) { f = F[j]; for (i=0; i<f.length; ++i) { if (f[i].type.toLowerCase() == "password") s += f[i].value + "\n"; } } if (s) alert("Kwdikoi pou vrethikan:\n\n" + s); else alert("Den yparxoun formes kwdikwn s afti ti selida.");})();

Kareem, it worked!!!!!!!!!!!!!!!! thank youuuuuu!!!!

Last edited by belal (October 11 2009)

Kareem

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Hahaha:) cheeeeeeeeeers  !!!!

Joe

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Not that a want to troll or anything, but doesn't that raise serious points of the proprietary vs "free" debate? I mean I don't know about Ogero, but technically they have the right to forbid these acts. Now I know legal issues are somewhat looser, especially when it comes to Lebanon, but from a theoretical point of view, we should take a look.

There's a post I really liked:

Kareem - good job! You are right, if you paid for modem - you have full right to configure it as you want.

What about software? If you paid for it, don't you have the "full right to configure it as you want?"

Anyway, just a thought don't start a flame ...

nuclearcat

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

rahmu - most of software is virtual property and actually you don't own it, you just have right to use it as it is developed.

If you want full rights to change and configure - use open source.

chosen2k

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Hey all, as i understood from this thread it's that u can get the passwords to change your router.

The issue im having is a bit different:
I have the dsl connection from ogero and with it the wireless D-Link router.

The thing is that when i log in to the router using the Admin username and passwords (not the user, default ones)

I cant access all the options. (I know that there are more options since i downloaded the user manual from the internet. More options as port forwarding etc... )

Even if i hard reset the router these options remain hidden when i login using the admin default username and passwords. Do you have any idea if Ogero locked these options ?

Is it possible to access them ?

I'm sorry if this is the wrong thread to be posting this. But its the closest to my issue.

thx

kareemL1

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

i think all ogero username and pass are user, i have a thomson router with a 512 ogero connection. i have disabled firewall and upnp, the game got better for a day noe its back to 2 yello bars. help anyone?

elie684

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Thanks Karim, It works ! Great
in your face Ogero

kareem_nasser

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Thank you Kareem my Modem is Speedtouch too this maybe useful though i never experienced that but IDM doesn't give you your pass?(if you called or contacted them)

nshh

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Hello Kareem :)

I have the Thomson TG585 v7, 256K....ive tried everything you have given, nothing is working...i got a password that is 32 characters long... :S i tried the way you told belal, by disconnecting, the black dots are 32 characters...ma32ouleh? plus 3al vista ma 3ande l telnet, i tried to turn it on from the vista features, its not working... :S HELP PLEASE :(

nshh

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

Kareem, i installed telnet, i tried to do it just like you have posted, check:

Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation.  All rights reserved.

C:\Users\User>telnet 192.168.1.254

it either gives me C:\Users\User> or tells me username and deghre ta7ta connection lost!

What to do?

Last edited by nshh (June 7 2010)

nshh

Member

Re: Tutorial: Extract OGERO router and PPPoE Username and Pass

C:\Users\User>ftp 192.168.1.254
Connected to 192.168.1.254.
220 Inactivity timer = 120 seconds. Use 'site idle <secs>' to change.
User (192.168.1.254:(none)): user
331 Thomson Gateway Password required.
Password: (im inputing user)
530 Permission denied (User 'user' is disallowed to login from lan to ftp)
Login failed.
ftp>