Akh man be careful! I hope you only got electrocuted by a low-voltage DC current. I've tried getting electrocuted by 220V, and let me tell you, it's not pleasing at all. I looked behind me to see who was shaking me. Thank goodness it was only shaking, and a little red fingertip. If you have no experience with electronics, wear protective gloves, or don't work with "naked" electronics. You may have shorted the board too. You're a very lucky man.Leonedes wroteWell I tried removing it directly, it was easily removable since it was attached to the ups' board by two very small pins, I think it can be attached again to work but as you may have noticed I have no experience with electronics at all. My question is, I got electrocuted by accident while I turned the ups back on, yes I stupidly tried touching the board, is that normal for the ups or does it have something to do with the fact that I removed the beeper ?
How to remove the beep sound from your ups
Well, I think it was only a 12V DC , I actually had the curiosity to check it out directly after getting electrocuted, I have a very small almost miniature Voltmeter that is used to measure extremly low voltages, mainly AA batteries, anyway I measured the place I got electrocuted, at first it gave 12V , then the screen suddenly gave 12,345,6 V and then it exploded in my HAND ! :P There were a few sparks then smoke came out of it - Very weird indeed, but anyway, I put back the lid and touched the cover everywhere without getting electrocuted to make sure it wont cause any problems (yes I had the heart :P)
Bas in any case, the board shouldn't electrocute anyone usually right ? I was curious cause laptop and desktop boards don't do that usually ...
Bas in any case, the board shouldn't electrocute anyone usually right ? I was curious cause laptop and desktop boards don't do that usually ...
- Edited
@leo wear slippers and you can touch everything (but you shouldn't unless your a cyborg who feeds on energy) :P
you shouldn't be in contact with the ground (barefoot) when handling electronics, even touching your pc case
you shouldn't be in contact with the ground (barefoot) when handling electronics, even touching your pc case
My UPS was considerate enough to stop beeping, on its own, a few months ago. I guess it got tired of beeping every day several times a day.
When I get a new UPS I'll definitely follow your instructions, the quiet is nice.
When I get a new UPS I'll definitely follow your instructions, the quiet is nice.
Just attach a small magnet on the speaker, it will be muted, (don't know if it can brick the speaker :/)
that's because most of speakers are made of a small magnet with a piece of copper rolled arround it,and another piece of copper rolled around the edge,both piece of copper attached to each other,and a sealing paper,so putting a magnet on the top of the speaker may ruin the magnetic field of the speaker and make it stop.TPR0 wroteJust attach a small magnet on the speaker, it will be muted, (don't know if it can brick the speaker :/)
Yes, it may damage the cone (paper). Well, i think its an effective solution...m.sabra wrotethat's because most of speakers are made of a small magnet with a piece of copper rolled arround it,and another piece of copper rolled around the edge,both piece of copper attached to each other,and a sealing paper,so putting a magnet on the top of the speaker may ruin the magnetic field of the speaker and make it stop.TPR0 wroteJust attach a small magnet on the speaker, it will be muted, (don't know if it can brick the speaker :/)
9 days later
Well What I did is that I got a pin and -In a Very Crazy and mad way- pecked into the hole of the speaker which decreased the sound dramatically so if the tv is on or any sound is on I won't hear it (I use the UPS for the Ps3) And thank god I didn't get electrocuted THANKS MAN
10 years later
Hello
I tried to fill some tiny 3M pieces in the buzzer hole thanks to a toothpick, then I sticked a round 3M patch on top, unfortunately the buzzer is still like 50% loud which is enough to bother me when sleeping. I have found this video as I don't want to mess up with the board, do you think it will work without electric shock if UPS unplugged from wall but battery still plugged? I will use a plier to remove the cap then a wooden toothpick to remove the metallic disc
https://youtu.be/cNZ-w5XYVZ8
I tried to fill some tiny 3M pieces in the buzzer hole thanks to a toothpick, then I sticked a round 3M patch on top, unfortunately the buzzer is still like 50% loud which is enough to bother me when sleeping. I have found this video as I don't want to mess up with the board, do you think it will work without electric shock if UPS unplugged from wall but battery still plugged? I will use a plier to remove the cap then a wooden toothpick to remove the metallic disc
https://youtu.be/cNZ-w5XYVZ8
14 days later
- Edited
simply remove the buzzer from the board and solder to wire and take them out of ups box,put a single line switch on any wire and then you can activate and deactivate buzzer any time
note: of course be sure that ups is disconnected from electricity also remove positive wire from battery for safety
note: of course be sure that ups is disconnected from electricity also remove positive wire from battery for safety
check if you can mute it by tapping the power button once (it should be mentioned in the manual), it will start beeping when the battery is low.